misteRate.info

Good enough for twigs and leaves — excellent value

Summary:
Works well for my purposes, which include a lot of twigs, leaves, brush, and ½” to ¾” sticks. The mulch produced is much finer than I expected, and is really smaller than your typical double-shredded commercial mulch. Assembly took 1½ hours, and was pretty straightforward, but no thanks to the instructions supplied with the unit. For the price, this is a very good unit.

Shipment:
Unit came 2 days after I ordered. Surprised at the speed for free shipping, but I noticed Amazon used 2nd day UPS air. I don’t know if this was expedited shipping because of the nearness of Xmas, but I was very pleased with the timeliness.

Assembly:
Instructions that came with the unit were very sparse and provided very limited illustrations and narrative to help the consumer. A clear and detailed picture or diagram would help a lot.

However, after staring at the photo on the box, and looking at the various parts that came in the box, assembly was simple enough for my son and I (you really need 2 people). Thinking back on it, here is the sequence that should be followed (little of this is in the instruction manual):

1. First start with the leg, axle, and wheel assembly. Look at the axle, and you will see two hex bolts with no apparent purpose screwed into the axle: one at each end. These are adjustment blanks that should be moved in order to properly align the leg, axle, and wheel assembly to accept the body of the shredder. You will notice an empty threaded hole immediately adjacent to these hex bolts, each a bit closer to the ends of the axle. Unscrew the hex bolts using the provided hex-key and move them to the adjacent holes that are closer to the end of the axle.
2. Place one wheel on the axle and secure with the supplied large flat washer followed by a cotter pin. Bend the end of the cotter pin around the axle end to secure the wheel. Do not put the other wheel on the axle yet, and don’t put on the McCulloch wheel covers on either wheel yet.
3. Thread the end of the axle through the opening on one leg (it doesn’t matter which one - they are symmetrical), and then use the supplied long hex bolt, lock washer and flat washer to loosely secure (hand tighten) the part of the axle closest to the attached wheel against one leg. The lock washer should be placed on the bolt first (closest to the bolt head) followed by the flat washer, then thread the bolt through the outer curved part of the leg into the threaded hole in the axle which is closest to the wheel that you put on in step 2.
4. Take the other leg and attach it to the other end of the axle using the remaining long hex bolt, lock washer, and flat washer — hand tighten.
5. Take the remaining wheel and secure it on the remaining axle end with the supplied large flat washer followed by a cotter pin. Do not put either wheel cover on until the end (just in case you did something wrong or you aren’t quite satisfied with the alignment).
6. Insert the solid aluminum barrels (each with two smooth-bore holes) into the end of the leg, axle, and wheel assembly that will mate with the shredder body. Line up the barrel holes with the leg holes. This provides strength at the connection point to the body. Put the leg, axle, and wheel assembly aside for the moment.
7. Now let’s work on the body. Using two persons to lift, stand the shredder body up on the flat pieces of cardboard supplied in the box. Unscrew the three black plastic-knobbed hand bolts that retain the yellow metal hood onto the black shredder assembly. Remove the yellow metal hood and put it aside. You have now exposed the heads of the four hex bolts used to secure the shredder body to the leg, axle, and wheel assembly.
8. Using the stronger person to lift, place the black shredder assembly over the leg/axle/wheel assembly, and line up the two holes on either leg (four holes total), with the four hex bolts on the black shredder assembly. Have your partner guide the bolts through the holes. From the underside, secure the bolts using the supplied flat washers, followed by lock washers, followed by nuts — hand tighten. Don’t put the hood back on yet.
9. Eyeball the entire assembly to see that is aligned vertically and horizontally. Since you only hand-tightened the axle-leg and leg-body hex bolts, it is now pretty easy to adjust the alignment by simply moving the body relative to the legs, or moving the legs relative to the axle. Don’t worry, the set-up is pretty sturdy, it would be difficult to harm anything by pushing or pulling to gain proper alignment.
10. Once you are satisfied with the alignment, tighten the two leg-axle hex bolts and four leg-body bolts using the supplied hex wrench. Use rotation tightening like you would when working on your car. Half tighten bolts on opposite ends, then ¾ tighten, and then full tighten.
11. Snap on the McCulloch wheel covers on the wheels.
12. Place the yellow metal hood back on top, and tighten the black plastic-knobbed hand bolts.
13. Place the black plastic leaf and twig receiving chute on top of the yellow metal hood, and line up the five small bolt holes. The ribbed side of the receiving chute should be facing toward the wheels. Insert and tighten the five bolts to secure the chute.
14. Turn off the switch before you plug in the shredder.

Operation:
1. For brush and sticks under ¾” this unit rocks! I am quite pleased how quickly this shredder takes the little stuff and spits out very finely shredded mulch.
2. For brush and sticks 1″ to 1½” - be careful! It is very easy to jam this unit by feeding big twigs too quickly. After jamming the unit, you need to turn it off, unplug it, remove the yellow metal hood by undoing the three black plastic-knobbed hand bolts, and then clearing the debris from the cutting blades or the large stick feeding tube on the yellow hood. I have found that the best approach is to feed twigs of this size using a feed a little, pause a little, feed a little, pause a little approach. You can actually do this pretty quickly once you get used to what the machine can handle as far as pace.
3. Leaves mixed with sticks seem to shred finer than leaves by themselves through the top chute.
4. Twigs by themselves, regardless of size, are consumed most quickly through the side feeder tube versus the top chute.

Update (2/9/2012): I also found some auctions for this item here.

The featured review for this product, McCulloch MCS2001 14 amp Electric Chipper/Shredder Lawn & Patio, was written by u12soccercoach.

The average rating for this item is 3.7 out of 5 stars, according to 3 reviews.